HTML  Plain   



General Information   |   Specifications   |   Drawings

Specifications  

The incredible success and popularity of the Mumm 30 and Corel 45 have led to a need for an in between sized boat and hence the Farr® 40 One Design was conceived. Using the same tried and tested configuration of simple carbon fiber swept spreader rig, no running backstays, non overlapping jibs and high stability keel, the Farr® 40 One Design provides those seeking the excitement and performance exhibited by the Mumm 30 and Corel 45 in a mid sized boat. Also compatible with the IMS Rule, the Farr® 40 One Design has proven to be a highly versatile boat that can be competitively raced under the IMS, CHS and PHRF handicapping systems. The pure simplicity and high performance characteristics are making this a very popular boat.

Rig Dimensions

IM 16.20 m / 53.2 ft
J 4.71 m / 15.5 ft
P 16.70 m / 54.8 ft
E 5.90 m / 19.4 ft
ISP 16.20 m / 53.2 ft
SPL 4.71 m / 15.5 ft

Construction

  • Epoxy/E-glass/Foam/Balsa composite wet Pre peg, post cured in oven
  • Keel mast support structure: Aluminium grid
  • Keel: steel fin, lead bulb, epoxy coated

Mechanical

  • Diesel engine: Yanmar Sail drive 3GMSD30
  • Two bladed geared folding propeller
  • Fuel tank: 75 Litre aluminium
  • Fuel and water separator
  • Single lever Throttle and gear control
  • Fuel gauge
  • Waterlock with silencer

Electrical

  • 12 Volt DC distribution panel
  • Battery condition meter
  • Circuit breakers of appropriate amperage
  • Main battery switch
  • Batteries: 2 x 105 Amp hour
  • Alternator, 80 Amp on engine
  • ORC approved navigation lights
  • Red and white dome lights for general illumination
  • Halogen reading lights
  • Plumbing and Stove
  • Water tanks: 2 x 80 litre
  • Pressurised water system
  • Galley sink with overboard drain
  • Vanity sink with overboard drain
  • Manual bilge pumps: 1 Cockpit, 1 below deck
  • Electric bilge pump below deck
  • Marine head c/w holding tank and overboard discharge
  • Flush seacocks on all openings below DWL
  • Fresh water fill below deck
  • Icebox
  • Stove: custom 3-burner Butane

Deck Hardware

  • Winches:
  • Primaries: Harken 48/3 speed (2)
  • Halyards: Harken 44/2 speed (2)
  • Mainsheet: Harken 44/2 speed (2)
  • Backstay: Hydraulic
  • Winch Handles: 10" Double grip lock (2)
  • 10" Single grip lock (2)
  • Pulpits: S/S custom bow and stern rails with lights
  • Stanchions: 6 tapered, 4 tapered with braces
  • Stanchion bases: Custom flush fit
  • Lifelines: Upper and lower 1 x 19 s/s wire
  • Rope clutches for halyards and pole lift
  • Jib tracks, fully adjustable with underdeck control lines
  • Barberhaul system 10:1
  • Cunningham led aft to mainsheet trimmer
  • Outhaul led aft to mainsheet trimmer
  • Mainsheet along boom 'European' style, led aft under deck
  • Spinnaker Foreguy
  • Forehatch: 24" diameter round alloy
  • Cockpit hatches: 5 x 12 (2)

Steering

  • Carbon rudder stock with Epoxy/Carbon/E-glass Blade
  • Upper and lower self-aligning Spherical bearings
  • Custom alloy tiller (standard)
  • Tiller extension
  • Wheel steering (optional)
  • Spars and Rigging
  • Custom carbon rig:
  • Two sets aft swept spreaders
  • Custom hydraulic mast step
  • Integrally moulded deck collar
  • Roller bearing spinnaker pole track
  • Aluminium boom: Outhaul, lock offs for reef lines (2)
  • Vang: solid strut led aft port and starboard
  • Carbon spinnaker pole
  • Standing rigging: discontinuous rod
  • Permanent backstay: Kevlar to hydraulic cylinder
  • Tuff Luff headfoil system
  • Running Rigging
  • Main halyard x 1
  • Forward Halyards x 3
  • Mainsheet x 1
  • Outhaul x 1
  • Cunningham x 1
  • Traveller control x 2
  • Jib sheets x 2
  • Jib in-haul x 2
  • Jib car adjust x 2
  • Spinnaker sheets x 2
  • Spinnaker brace x 2
  • Foreguy (2:1) x 1
  • Backstay strop x 1
  • Spinnaker tweeker lines x 2

Miscellaneous

  • Exterior finish: Light colour gel coat on topsides and deck
  • Clear epoxy on bottom ready to sand and paint
  • Foils are epoxy coated and faired to template
  • Interior finish in matt white paint
  • Four fixed berths: 4" cushions
  • Fabric covers on hanging lockers
  • Customers can order custom paint schemes as an option. Please contact us for a full list of options.

One-Design

Guaranteed to comply with Farr® 40 One Design class rules on delivery

 

Farr®, ® and ® are registered trademarks of Farr Yacht Design, Ltd.